Gravity air quality sensor CCS811 I2C Botland Robotic Shop
This sensor is great for monitoring air quality, in a compact plug-in format. Best of all, unlike almost all other sensors we've seen that are UART interface, this one is I2C interface, which makes it a great match for single-board Linux computers like Raspberry Pi, or even plain Arduino UNO's that normally would use software serial.
Mics6814 Carbon Monoxide Nitrogen Oxygen Compact Sensor Co/No2/Nh3 in Pakistan
This ENS160 Air Quality Sensor (I2C), based on ScioSense's new ENS160 sensor chip, is specifically designed for indoor air quality monitoring and offers detection of multiple IAQ data (TVOC, eCO2, AQI).
8.49 MQ135 Air Quality Sensor (Arduino & Pi Compatible) Tinkersphere
Description Discontinued - you can grab the Adafruit SGP30 Air Quality Sensor Breakout - VOC and eCO2 - STEMMA QT / Qwiic instead! Breathe easy - we finally have an I2C VOC/eCO2 sensor in the Adafruit shop! Add air quality monitoring to your project and with an Adafruit CCS811 Air Quality Sensor Breakout.
Air Quality Monitor with 1602 LCD Hackster.io
Breathe easy - we finally have an I2C VOC/eCO2 sensor in the Adafruit shop! Add air quality monitoring to your project and with an Adafruit CCS811 Air Quality Sensor Breakout. This sensor from AMS is a gas sensor that can detect a wide range of Volatile Organic Compounds (VOCs) and is intended for indoor air quality monitoring.
PM2.5 Air Quality Sensor with I2C Interface PMSA003I ID 4505 39.95 Adafruit Industries
This ENS160 Air Quality Sensor (I2C), based on ScioSense's new ENS160 sensor chip, is specifically designed for indoor air quality monitoring and offers detection of multiple IAQ data (TVOC, eCO2, AQI).
CCS811 Air Quality Sensor I2C Mini Module NCD Store
I2C Wiring Wiring the PMSA300I is made simple by using the I2C interface either via the STEMMA QT connector or a solderless breadboard. Connect PMSA300I VCC (red wire) to Arduino 5V if you are running a 5V board Arduino (Uno, etc.). If your board is 3V, connect to that instead. Connect PMSA300I GND (black wire) to Arduino GND
Air Quality Sensor Sgp30 Air Quality Sensor Breakout Elmwood Electronics The monitor will
Breathe easy - we finally have an I2C VOC/eCO2 sensor in the Adafruit shop! Add air quality monitoring to your project and with an Adafruit CCS811 Air Quality Sensor Breakout. This sensor from AMS is a gas sensor that can detect a wide range of Volatile Organic Compounds (VOCs) and is intended for indoor air quality monitoring.
Air Quality Sensor CCS811 Arduino Hookup
Overview Breathe easy - we finally have an I2C VOC/eCO2 sensor in the Adafruit shop! Add air quality monitoring to your project and with an Adafruit CCS811 Air Quality Sensor Breakout. This sensor from AMS is a gas sensor that can detect a wide range of Volatile Organic Compounds (VOCs) and is intended for indoor air quality monitoring.
Indoor I2C ENS160 Air Quality Sensor compatible for Arduino and Raspberry Pi DFRobot
Arduino Code | PM2.5 Air Quality Sensor | Adafruit Learning System Arduino Code Subscribe Using the PM2.5 with Arduino is a simple matter of wiring up it to your Arduino-compatible microcontroller, installing the Adafruit PM25AQI library we've written, and running the provided example code.
PM2.5 Air Quality Sensor with I2C Interface — PMSA003I Raspberry Pi в Киеве (Украина)
This sensor uses laser scattering to radiate suspending particles in the air, then collects scattering light to obtain the curve of scattering light change with time. The microprocessor calculates equivalent particle diameter and the number of particles with different diameters per unit volume.
CO2, Temperature, Humidity, Brightness (WIFI) sensor IOT Factory
The I2C pins are also 3V and 5V compliant. The last category contains three more pins. INT is an interrupt output pin that the sensor uses to signal that a new reading is ready, or when the sensor detects a dangerous condition. The WAKE pin enables or disables the sensor. Pull it low to turn on the sensor.
SGP30 Air Quality Sensor Breakout VOC and eCO2 เซนเซอร์วัดคุณภาพอากาศ SGP30 ArduinoAll ขาย
Looking For I2c Sensor? We Have Almost Everything On eBay. But Did You Check eBay? Check Out I2c Sensor On eBay.
Got an I2C air qualitysensor to work with my LORaWAN Stm32 board and transmit to TTN! electronics
19 Overview Breathe easy with the SGP30 Multi-Pixel Gas Sensor, a fully integrated MOX gas sensor. This is a very fine air quality sensor from the sensor experts at Sensirion, with I2C interfacing and fully calibrated output signals with a typical accuracy of 15% within measured values.
CCS811 Air Quality Sensor I2C Mini Module NCD Store
The Air Quality Index (AQI) value anything above 50 is unhealthy for breathing. So, when the pollution level exceeds in air, the fan turns on automatically to blow fresh air. Instead of Fan, you can use any other air freshening device like a humidifier connected to the relay. Bill of Materials
4 in 1 BME680 I2C + STM32 (UART) Temperature, Humidity, Pressure and Gas Sensor ขาย Arduino
This sensor uses laser scattering to radiate suspending particles in the air, then collects scattering light to obtain the curve of scattering light change with time. The microprocessor calculates equivalent particle diameter and the number of particles with different diameters per unit volume.
MODBUS PWM I2C air quality sensor SCD30 module CO2 RH /T measurements CO2SENSOR £41.87
Breathe easy - we finally have an I2C VOC/eCO2 sensor in the Adafruit shop! Add air quality monitoring to your project and with an Adafruit CCS811 Air Quality Sensor Breakout. This sensor from AMS is a gas sensor that can detect a wide range of Volatile Organic Compounds (VOCs) and is intended for indoor air quality monitoring.